Curly Twirly Ballerina Necklace

This Curly Twirly Ballerina Necklace is a great feminine statement necklace that would look flattering on any woman.  Made with soft pink rose beads, this DIY necklace makes a wonderful Mother's Day or birthday gift.  Celebrate your inner goddess with this sweet Ballerina Necklace.

Materials:

• Artistic Wire Coiling Gizmo
• Wood Plaque-Rectangle-5 x 7 inch
• Beadalon® Coiling Gizmo
• Copper Wire-Sterling Silver Plated-26 Gauge
• Drill
• Phillips Screwdriver
• You’ll need the wood plaque as a base for the coiling gizmo
• Semi-Precious Bead Strand-Rose Quartz-13 x 18mm
• Semi Precious Stone Bead Strand-Oval-Rose Quartz
• Semi-Precious Bead Strand-Rose Quartz-Chips
• Crimp Beads-Silver-1.3mm
• Lobster Clasp-Sterling Silver Plated-12mm
• Double Rings-Sterling Silver Plated-7 mm-Value Pack
• Head Pin-Nickel Plated-2 in
• Eye Pin-Nickel Plated-2 in
• 49 Strand Beadalon® Wire-sterling silver plated-.018 in
• Crimp tool
• Wire cutters
• Round nose pliers
• Flat nose pliers

Instructions:

1. Simply drill a pilot hole in the center of the plaque and then screw the bracket into it. Screw it down tight. This gives the bracket stability while you are coiling.
    
2. To make the coiled beads I recommend this video from Beadalon: Artistic Wire Deluxe Coiling Gizmo. The coiling gizmo shown is slightly different but the coiled wire bead I created is shown here. It’s the best video I’ve found for showing how they are made.
   
   
    
3. You’ll need six coiled beads for this necklace.
    
4. I used 26 gauge wire for my necklace because I wanted something delicate. The wire is very thin and if this is your first project with the coiling gizmo you might want to move up to the Copper Wire-Sterling Silver Plated-24 Gauge just to make it a little easier on yourself.
    
5. To create the center of the necklace put an eye pin through one of the large Rose Quartz Beads and make a simple loop at the top. Put 2 rose quartz chips on 2 head pins and 3 rose quartz chips on another head pin. Create a simple loop and attach them all to the bottom of the eye pin as shown.
   
   
    
6. Make wire wrapped loops on the end of all of the coiled wire beads and attach two of them to the top of the stone using the simple loop you created earlier.
   
   
    
7. The next segment is created by putting an oval rose quartz on an eyepin and attaching them to the coiled beads. Add another pair of coiled beads followed by a head pin with 5 rose quartz chips. Finally, add a third coiled bead on each side.
   
   
    
8. Attach a length of Beadalon wire to one of the last coiled beads with a crimp bead and bead with rose quarts chips. With a crimp bead attach one half of the closure.
    
9. Repeat on the second side.
    
10. This portion of the necklace will determine how long the final piece is. My finished strand of rose quartz chips is 4 1/4 inches long on each side and the finished necklace is 24 inches from tip to tip.
     
11. For the very last step, go back over the necklace with either a bit of old panty hose or a polyester/nylon fabric and very gently polish the coiled wire beads. If you left any wires poking out they will catch on the fabric and you’ll see where they may need to be trimmed off. This will keep the wires from poking your neck or snagging your clothing during wear.
     
12. Now all that’s left is to decide whether you will give this necklace away or keep it for yourself!